13.3 inch capacitive touch panel
13.3 inch is the size we ship most often to medical and test-equipment builders — large enough for a graph, small enough to fit a bench instrument.
FOB Shenzhen, G+G panel with controller and 1.8 m USB cable, 1–50 pcs. Custom coating, glass thickness and printed border quoted on drawing.
Panel, controller and cable in one carton
One G+G panel at 314 × 186 mm, the matched controller, a 1.8 m USB cable and the FPC tail you specified. Below 32 inch this ships from stock; above it, panels are built per order in two to three weeks.
- OD 314 × 186 mm · VA 294 × 166 mm · border 10 mm
- 6 H glass, 10-point, USB / I2C / RS232 controller included
- 412 pcs in stock
Cable and tail. 1.8 m USB cable as standard. I2C, RS232 and longer tails are the same price, specified at the drawing stage.
Controller included. Every panel ships with a matched controller, flashed and tested against that panel — not a generic board.
Three numbers, not one
Unlike an infrared frame, a capacitive panel is defined by three dimensions. The OD is the outside of the glass and is what your housing is cut to. The VA is the visible area your UI is designed against. The sensor is the ITO pattern inside the printed border.
| Outline (OD) | 314 × 186 mm |
| Active area (VA) | 294 × 166 mm |
| Sensor | 306 × 178 mm |
| Printed border | 10 mm typical, 6 mm minimum |
Typical builds at this size: medical device, test equipment, portable monitor.
Solid outline = OD 314 × 186 mm · dashed = VA active area 294 × 166 mm
13.3 inch panel — options and unit price
| Configuration | 1–9 pcs | 10–49 pcs | 50–199 pcs | 200+ pcs |
|---|---|---|---|---|
| G+G, 1.1 mm glass | $76 | $70 | $65 | $58 |
| G+FF, 1.1 mm glass | $67 | $61 | $56 | $51 |
| + 2.0 mm glass | + $9 | + $8 | + $8 | + $7 |
| + AG anti-glare coating | + $6 | + $6 | + $5 | + $5 |
13.3 inch panel — full specification
| Mechanical | |
| Adopted size | 13.3" 16:9 |
|---|---|
| Outline (OD) | 314 × 186 mm |
| Active area (VA) | 294 × 166 mm |
| Sensor size | 306 × 178 mm |
| Total thickness | 1.6 mm (1.1 mm glass) / 2.3 mm (1.8 mm) |
| Optical & touch | |
| Surface hardness | ≥ 6 H |
| Touch points | 10 (up to 40 on large format) |
| Transparency | ≥ 85 % |
| Haze | < 3 % (AG 3–8 % optional) |
| Response time | ≤ 10 ms |
| Accuracy | ± 1.5 mm |
| Touch life | > 10 million touches |
| Interface & environment | |
| Interface | USB HID / I2C / RS232 |
| Report rate | ≥ 100 Hz |
| Operating temperature | −20 °C to +70 °C |
| Operating system | Windows, Android, Linux, Chrome OS |
| Certification | CE, FCC, RoHS |
What happens after the carton is open
A capacitive panel needs no calibration — the sensor is bonded to the glass, so the coordinates are geometry rather than measurement. What it does need is the right settings for your glass stack, and a bonding process that does not trap air.
Plug and play over USB
Windows, Android, Linux and ChromeOS pick it up as a HID touch digitizer with nothing installed. I2C and RS232 versions available for boards without a USB host.
Firmware tuned to your stack
Threshold, report rate, edge suppression and ESD level are set for the cover glass you specify — then shipped as a settings file you can clone across a batch.
Bonding and install guidance
OCA versus tape versus air gap, FPC bend radius, shield grounding under 4 Ω. We will join the first bonding run by video if it is your first one.
13.3 inch panel questions
What are the OD, VA and sensor sizes of the 13.3 inch panel?
Can I change the cover glass thickness?
Is a controller and cable included?
What is the lead time?
Is this a capacitive touch screen or only a panel?
Capacitive touch screen, capacitive touch TP, or panel
The stack-up wording matters more than the product name. G+G is glass sensor plus glass cover, G+FF is film sensor plus film, and G+F is glass plus one film. Same part number format, different thickness, cost and durability — the difference is spelled out in the stack-up guide.
Where these panels end up: kiosks, HMI, medical instruments, retail signage — capacitive touch applications →
Tell us the size. We will tell you what fits.
Send a drawing, a size, or just a photo of the screen you are building around. Our engineers reply with a matched part and a price within 12 working hours.