17.0 inch capacitive touch panel
17 inch 16:10 panels go into machine tools and gaming cabinets where the enclosure is already cut for that format.
FOB Shenzhen, G+G panel with controller and 1.8 m USB cable, 1–50 pcs. Custom coating, glass thickness and printed border quoted on drawing.
Panel, controller and cable in one carton
One G+G panel at 388 × 251 mm, the matched controller, a 1.8 m USB cable and the FPC tail you specified. Below 32 inch this ships from stock; above it, panels are built per order in two to three weeks.
- OD 388 × 251 mm · VA 366 × 229 mm · border 11 mm
- 6 H glass, 10-point, USB / I2C / RS232 controller included
- 352 pcs in stock
Cable and tail. 1.8 m USB cable as standard. I2C, RS232 and longer tails are the same price, specified at the drawing stage.
Controller included. Every panel ships with a matched controller, flashed and tested against that panel — not a generic board.
Three numbers, not one
Unlike an infrared frame, a capacitive panel is defined by three dimensions. The OD is the outside of the glass and is what your housing is cut to. The VA is the visible area your UI is designed against. The sensor is the ITO pattern inside the printed border.
| Outline (OD) | 388 × 251 mm |
| Active area (VA) | 366 × 229 mm |
| Sensor | 380 × 243 mm |
| Printed border | 11 mm typical, 6 mm minimum |
Typical builds at this size: machine tool hmi, gaming cabinet, lab instrument.
Solid outline = OD 388 × 251 mm · dashed = VA active area 366 × 229 mm
17.0 inch panel — options and unit price
| Configuration | 1–9 pcs | 10–49 pcs | 50–199 pcs | 200+ pcs |
|---|---|---|---|---|
| G+G, 1.1 mm glass | $105 | $97 | $89 | $80 |
| G+FF, 1.1 mm glass | $92 | $84 | $78 | $70 |
| + 2.0 mm glass | + $13 | + $12 | + $10 | + $9 |
| + AG anti-glare coating | + $8 | + $8 | + $7 | + $6 |
17.0 inch panel — full specification
| Mechanical | |
| Adopted size | 17.0" 16:10 |
|---|---|
| Outline (OD) | 388 × 251 mm |
| Active area (VA) | 366 × 229 mm |
| Sensor size | 380 × 243 mm |
| Total thickness | 1.6 mm (1.1 mm glass) / 2.3 mm (1.8 mm) |
| Optical & touch | |
| Surface hardness | ≥ 6 H |
| Touch points | 10 (up to 40 on large format) |
| Transparency | ≥ 85 % |
| Haze | < 3 % (AG 3–8 % optional) |
| Response time | ≤ 10 ms |
| Accuracy | ± 1.5 mm |
| Touch life | > 10 million touches |
| Interface & environment | |
| Interface | USB HID / I2C / RS232 |
| Report rate | ≥ 100 Hz |
| Operating temperature | −20 °C to +70 °C |
| Operating system | Windows, Android, Linux, Chrome OS |
| Certification | CE, FCC, RoHS |
What happens after the carton is open
A capacitive panel needs no calibration — the sensor is bonded to the glass, so the coordinates are geometry rather than measurement. What it does need is the right settings for your glass stack, and a bonding process that does not trap air.
Plug and play over USB
Windows, Android, Linux and ChromeOS pick it up as a HID touch digitizer with nothing installed. I2C and RS232 versions available for boards without a USB host.
Firmware tuned to your stack
Threshold, report rate, edge suppression and ESD level are set for the cover glass you specify — then shipped as a settings file you can clone across a batch.
Bonding and install guidance
OCA versus tape versus air gap, FPC bend radius, shield grounding under 4 Ω. We will join the first bonding run by video if it is your first one.
17.0 inch panel questions
What are the OD, VA and sensor sizes of the 17.0 inch panel?
Can I change the cover glass thickness?
Is a controller and cable included?
What is the lead time?
Where is a panel this size normally used?
The names this part travels under
On a specification you will also meet PCAP and projected capacitive touch panel, which describe the sensing method rather than the part: a grid of ITO electrodes projected through the cover glass. Every panel on this site is projected capacitive, so the two terms are not a different product line — they are a more precise name for the one you are looking at.
Where these panels end up: kiosks, HMI, medical instruments, retail signage — capacitive touch applications →
Tell us the size. We will tell you what fits.
Send a drawing, a size, or just a photo of the screen you are building around. Our engineers reply with a matched part and a price within 12 working hours.