32 inch infrared touch frame
At 32 inch the whole frame ships as one parcel, which is why most kiosk builders start here. It is also the cheapest way to test a new enclosure before committing to a larger tool.
FOB Shenzhen, frame only, 1–50 pcs. Add $30 for 3 mm tempered glass. Volume tiers quoted on request.
What is in the 32 inch box
One frame at 734 × 428 mm, one controller board, a 1.8 m USB cable and four mounting brackets. Glass is separate — add it only if your housing does not already carry a front sheet.
- 734 × 428 mm outer, 708 × 398 mm active area
- 2–40 touch points, USB HID, no driver for Windows, Android or Linux
- 412 pcs in stock, leaves in 3–7 days
Corner joint. Cast corner block pinned into the extrusion — this is what keeps an 86 inch frame flat instead of bowing in the middle.
Packing. One frame per cardboard tube with foam ends. Crates start at 98 inch, where a tube stops being practical.
What the 32 inch frame fits
The active area is 708 × 398 mm — a standard 32 inch 16:9 panel. The frame adds 13 mm on three sides and 19 mm at the bottom, which is where the controller PCB and USB cable sit.
- Outer frame: 734 × 428 mm, 9.5 mm deep
- Housing cut-out: leave 738 × 432 mm plus 3 mm clearance for the cable
- Glass clearance: up to 5 mm thick; 8 mm with the wide-gap version
- Mounting: front-flush with M3 inserts, or side brackets
Typical builds at this size: self-order kiosk, access control terminal, small wayfinding unit.
32 inch frame — options and unit price
Indicative FOB Shenzhen prices at 10-point configuration. Higher touch counts add controller cost, not sensor cost, so the jump is smaller than most buyers expect.
| Configuration | 1–9 pcs | 10–49 pcs | 50–199 pcs | 200+ pcs |
|---|---|---|---|---|
| 10-point | $90 | $85 | $79 | $72 |
| 20-point | $90 | $85 | $79 | $72 |
| 32-point | $95 | $90 | $84 | $76 |
| 40-point | $101 | $95 | $89 | $81 |
| + 3 mm tempered glass | + $30 | + $27 | + $25 | + $22 |
32 inch frame — full specification
| Mechanical | |
| Adopted screen | 32" 16:9 (active area 708 × 398 mm) |
|---|---|
| Frame outer size | 734 × 428 mm (± 1.0 mm) |
| Bezel width | 13 mm side / 19 mm bottom (15.5 mm uniform optional) |
| Frame depth | 9.5 mm |
| Frame material | Aluminium alloy 6063, black anodised |
| Net weight | 1.4 kg |
| Touch performance | |
| Touch points | 2 / 4 / 6 / 10 / 16 / 20 / 32 / 40 |
| Resolution | 32,768 × 32,768 (interpolated) |
| Response time | ≤ 8 ms |
| Report rate | 200 Hz |
| Accuracy | ± 2 mm (typical, centre 90 % area) |
| Minimum touch object | 5 mm — 3 mm with fine-tip option |
| Electrical & interface | |
| Interface | USB 2.0 HID, plug-and-play; RS232 optional |
| Power | USB 5 V, < 200 mA |
| Operating system | Windows 7/10/11, Android, Linux, Chrome OS |
| Environment & compliance | |
| Operating temperature | −20 °C to +70 °C |
| Humidity | 10 – 90 % RH, non-condensing |
| Ambient light | Up to 30,000 lux (direct-sunlight model on request) |
| MTBF | ≥ 30,000 hours |
| Touch life | > 50 million touches |
| Certification | CE, FCC, RoHS |
Values are typical for this size. Guaranteed limits are stated on the datasheet issued with your order.
What happens after the carton is open
A frame is not finished hardware until it is calibrated against the display it sits on. Three things ship with this size to get you there, and none of them are extras.
No driver, on any system
USB HID digitizer. Windows 10/11, Android, Linux and ChromeOS enumerate it without installing anything. macOS reports single point only — worth knowing before you commit.
Calibration tool and profile
Windows and Linux builds, 4/9/25-point runs, written to the controller so it survives a power cycle. Stuck? A ten-minute remote session with our engineer calibrates it with you.
Installation sheet for this size
Clearance, 0.5 N·m torque, ground under 4 Ω, 3 m passive USB limit — plus the symptom table that covers most first-install problems.
Installation guide · Calibration & software · OS compatibility
32 inch frame questions
What is the outer size of a 32 inch frame?
Can I get this size with a different bezel?
How many units of the 32 inch frame fit in a carton?
Do you supply the tempered glass with the frame?
Is this an IR touch frame or an infrared touch screen?
What to write on the PO so it arrives correctly
In a BOM this line usually reads infrared touch frame kit or IR frame kit, because what ships is not just the aluminium: four extrusions, four corner blocks, one controller, one 1.8 m USB cable and four mounting brackets. The kit wording matters for customs and for your assembly line — a knocked-down frame is a component, not a finished appliance.
The most common build we ship is not a product at all — it is a retrofit. A shop, a school or a factory has a screen, and someone wants to press it. An overlay frame is the cheapest way to get there: no new display, no new mounting, no firmware.
If your enquiry uses a name not listed here, send it anyway — a photo of the old part or the housing opening settles it faster than any glossary. Full terminology list →
Tell us the size. We will tell you what fits.
Send a drawing, a size, or just a photo of the screen you are building around. Our engineers reply with a matched part and a price within 12 working hours.