WCIMCI Get a Quote

39.5 inch infrared touch frame

39.5 inch is a splice-wall size. Integrators rebuilding a video wall into a touch wall often have 39.5 inch panels left in stock, so the frame is built to that diagonal rather than to the nearest catalogue size.

900 × 522 mm10–40 pointsUSB HID13 mm bezel
Unit price · FOB Shenzhen
$105 / pc
In stock: 356 pcs
MOQ1 pc
Lead time3–7 days
Request quotation Ask about volume pricing

FOB Shenzhen, frame only, 1–50 pcs. Add $36 for 3 mm tempered glass. Volume tiers quoted on request.

39.5 inch infrared touch frame, 900 x 522 mm black anodised aluminium bezel with USB cable
Product photo

Inside the 39.5 inch frame

900 × 522 mm outside with a 13 mm side bezel and a 19 mm bottom rail. This is the same extrusion profile we run from 32 to 110 inch — the cut length changes, the section does not, so the frame in the photo is what arrives at every size in the range.

  • 900 × 522 mm outer, 874 × 492 mm active area
  • 2–40 touch points, USB HID, no driver for Windows, Android or Linux
  • 356 pcs in stock, leaves in 3–7 days
39.5 inch IR frame — ships knocked down

Ships knocked down. Four extrusions and four corners in one tube. Flat-packed freight runs about a third cheaper than a crated assembled frame.

39.5 inch IR frame — spare led tubes

Spare LED tubes. Tubes and filter strips are stocked for every size listed, so a dead emitter is a part swap rather than a new frame.

900 mm 522 mm frame outer · bezel 13 mm · active area 874 × 492 mm
Dimensions

What the 39.5 inch frame fits

The active area is 874 × 492 mm — a standard 39.5 inch 16:9 panel. The frame adds 13 mm on three sides and 19 mm at the bottom, which is where the controller PCB and USB cable sit.

  • Outer frame: 900 × 522 mm, 9.5 mm deep
  • Housing cut-out: leave 904 × 526 mm plus 3 mm clearance for the cable
  • Glass clearance: up to 5 mm thick; 8 mm with the wide-gap version
  • Mounting: front-flush with M3 inserts, or side brackets

Typical builds at this size: video wall rebuild, control room, lobby wall.

Price by configuration

39.5 inch frame — options and unit price

Indicative FOB Shenzhen prices at 10-point configuration. Higher touch counts add controller cost, not sensor cost, so the jump is smaller than most buyers expect.

Configuration1–9 pcs10–49 pcs50–199 pcs200+ pcs
10-point$105$99$92$84
20-point$105$99$92$84
32-point$111$105$98$89
40-point$118$111$103$94
+ 3 mm tempered glass+ $36+ $32+ $30+ $27
Note: prices are indicative and exclude freight, insurance and customs. Confirmed pricing is issued with your quotation and held for 30 days.
Specification

39.5 inch frame — full specification

Mechanical
Adopted screen39.5" 16:9 (active area 874 × 492 mm)
Frame outer size900 × 522 mm (± 1.0 mm)
Bezel width13 mm side / 19 mm bottom (15.5 mm uniform optional)
Frame depth9.5 mm
Frame materialAluminium alloy 6063, black anodised
Net weight1.7 kg
Touch performance
Touch points2 / 4 / 6 / 10 / 16 / 20 / 32 / 40
Resolution32,768 × 32,768 (interpolated)
Response time≤ 8 ms
Report rate200 Hz
Accuracy± 2 mm (typical, centre 90 % area)
Minimum touch object5 mm — 3 mm with fine-tip option
Electrical & interface
InterfaceUSB 2.0 HID, plug-and-play; RS232 optional
PowerUSB 5 V, < 200 mA
Operating systemWindows 7/10/11, Android, Linux, Chrome OS
Environment & compliance
Operating temperature−20 °C to +70 °C
Humidity10 – 90 % RH, non-condensing
Ambient lightUp to 30,000 lux (direct-sunlight model on request)
MTBF≥ 30,000 hours
Touch life> 50 million touches
CertificationCE, FCC, RoHS

Values are typical for this size. Guaranteed limits are stated on the datasheet issued with your order.

Commissioning

What happens after the carton is open

A frame is not finished hardware until it is calibrated against the display it sits on. Three things ship with this size to get you there, and none of them are extras.

⚡

No driver, on any system

USB HID digitizer. Windows 10/11, Android, Linux and ChromeOS enumerate it without installing anything. macOS reports single point only — worth knowing before you commit.

◎

Calibration tool and profile

Windows and Linux builds, 4/9/25-point runs, written to the controller so it survives a power cycle. Stuck? A ten-minute remote session with our engineer calibrates it with you.

⌗

Installation sheet for this size

Clearance, 0.5 N·m torque, ground under 4 Ω, 3 m passive USB limit — plus the symptom table that covers most first-install problems.

Installation guide  ·  Calibration & software  ·  OS compatibility

FAQ

39.5 inch frame questions

What is the outer size of a 39.5 inch frame?
900 × 522 mm with a 13 mm side bezel and 19 mm bottom bezel. The active area matches a standard 39.5 inch 16:9 panel at 874 × 492 mm. If your housing is already cut, send the cut-out dimension and we will check the clearance before you order.
Can I get this size with a different bezel?
Yes. 15.5 mm uniform bezel and 19 mm bottom are both available at the same price; anything wider than 20 mm is a custom extrusion and adds about a week to the lead time.
How many units of the 39.5 inch frame fit in a carton?
One frame per carton at this size, foam-packed, 5.0 kg gross. Ten cartons make a pallet, and a 20 ft container takes roughly 120 frames — we quote the container load if you give us the destination port.
Do you supply the tempered glass with the frame?
Yes — add $36 per unit for 3 mm tempered glass bonded into the frame. Most 39.5 inch builds order the frame alone because the front glass is already part of their display.
Does it come as a kit with the controller and cable?
Yes. Every frame leaves as a kit: the aluminium, four corner blocks, one controller board, a 1.8 m USB cable and four mounting brackets. Above 55 inch the frame itself is knocked down inside the tube, and reassembly is a screwdriver job with the one-page drawing we include.
Same part, other names

Naming, for the benefit of your purchasing team

Multi touch frame, infrared multi-touch frame, IR touch panel — all of them refer to the same assembly described on this page. The touch count is set by the controller and the LED pitch, not by the name, so a 10-point and a 40-point version are physically identical from the outside.

Two questions decide the fit on a retrofit: the lit area of the display (not the diagonal on the box) and whether the USB port stays alive when the screen sleeps. Get those right and the install is fifteen minutes with a screwdriver.

If your enquiry uses a name not listed here, send it anyway — a photo of the old part or the housing opening settles it faster than any glossary. Full terminology list →

Tell us the size. We will tell you what fits.

Send a drawing, a size, or just a photo of the screen you are building around. Our engineers reply with a matched part and a price within 12 working hours.

◉WeChat wm-lcd · scan or search the ID
◷Mon–Sat 09:00–18:00 GMT+8 · English & Chinese
Thanks — your request is with our engineering desk.
You will get a reply within 12 working hours, usually much sooner. If it is urgent, message WhatsApp +86 153 2343 9001 and quote your company name.

Or email us directly at info@wcimci.com. Drawings in DWG, STEP, PDF or DXF are all fine.

WhatsApp us