58 inch infrared touch frame
58 inch gets ordered by integrators filling a fixed opening — a lift lobby surround, a kiosk column, a wall recess built before the display was chosen. It is a fit-the-hole size rather than a volume one.
FOB Shenzhen, frame only, 1–50 pcs. Add $56 for 3 mm tempered glass. Volume tiers quoted on request.
Inside the 58 inch frame
1310 × 752 mm outside with a 13 mm side bezel and a 19 mm bottom rail. This is the same extrusion profile we run from 32 to 110 inch — the cut length changes, the section does not, so the frame in the photo is what arrives at every size in the range.
- 1310 × 752 mm outer, 1284 × 722 mm active area
- 2–40 touch points, USB HID, no driver for Windows, Android or Linux
- 296 pcs in stock, leaves in 3–7 days
Spare LED tubes. Tubes and filter strips are stocked for every size listed, so a dead emitter is a part swap rather than a new frame.
Ships knocked down. Four extrusions and four corners in one tube. Flat-packed freight runs about a third cheaper than a crated assembled frame.
What the 58 inch frame fits
The active area is 1284 × 722 mm — a standard 58 inch 16:9 panel. The frame adds 13 mm on three sides and 19 mm at the bottom, which is where the controller PCB and USB cable sit.
- Outer frame: 1310 × 752 mm, 9.5 mm deep
- Housing cut-out: leave 1314 × 756 mm plus 3 mm clearance for the cable
- Glass clearance: up to 5 mm thick; 8 mm with the wide-gap version
- Mounting: front-flush with M3 inserts, or side brackets
Typical builds at this size: lift lobby surround, kiosk column, wall recess.
58 inch frame — options and unit price
Indicative FOB Shenzhen prices at 10-point configuration. Higher touch counts add controller cost, not sensor cost, so the jump is smaller than most buyers expect.
| Configuration | 1–9 pcs | 10–49 pcs | 50–199 pcs | 200+ pcs |
|---|---|---|---|---|
| 10-point | $170 | $160 | $150 | $136 |
| 20-point | $170 | $160 | $150 | $136 |
| 32-point | $180 | $169 | $159 | $144 |
| 40-point | $190 | $179 | $168 | $152 |
| + 3 mm tempered glass | + $56 | + $50 | + $46 | + $42 |
58 inch frame — full specification
| Mechanical | |
| Adopted screen | 58" 16:9 (active area 1284 × 722 mm) |
|---|---|
| Frame outer size | 1310 × 752 mm (± 1.0 mm) |
| Bezel width | 13 mm side / 19 mm bottom (15.5 mm uniform optional) |
| Frame depth | 9.5 mm |
| Frame material | Aluminium alloy 6063, black anodised |
| Net weight | 2.2 kg |
| Touch performance | |
| Touch points | 2 / 4 / 6 / 10 / 16 / 20 / 32 / 40 |
| Resolution | 32,768 × 32,768 (interpolated) |
| Response time | ≤ 8 ms |
| Report rate | 200 Hz |
| Accuracy | ± 2 mm (typical, centre 90 % area) |
| Minimum touch object | 5 mm — 3 mm with fine-tip option |
| Electrical & interface | |
| Interface | USB 2.0 HID, plug-and-play; RS232 optional |
| Power | USB 5 V, < 200 mA |
| Operating system | Windows 7/10/11, Android, Linux, Chrome OS |
| Environment & compliance | |
| Operating temperature | −20 °C to +70 °C |
| Humidity | 10 – 90 % RH, non-condensing |
| Ambient light | Up to 30,000 lux (direct-sunlight model on request) |
| MTBF | ≥ 30,000 hours |
| Touch life | > 50 million touches |
| Certification | CE, FCC, RoHS |
Values are typical for this size. Guaranteed limits are stated on the datasheet issued with your order.
What happens after the carton is open
A frame is not finished hardware until it is calibrated against the display it sits on. Three things ship with this size to get you there, and none of them are extras.
No driver, on any system
USB HID digitizer. Windows 10/11, Android, Linux and ChromeOS enumerate it without installing anything. macOS reports single point only — worth knowing before you commit.
Calibration tool and profile
Windows and Linux builds, 4/9/25-point runs, written to the controller so it survives a power cycle. Stuck? A ten-minute remote session with our engineer calibrates it with you.
Installation sheet for this size
Clearance, 0.5 N·m torque, ground under 4 Ω, 3 m passive USB limit — plus the symptom table that covers most first-install problems.
Installation guide · Calibration & software · OS compatibility
58 inch frame questions
What is the outer size of a 58 inch frame?
Can I get this size with a different bezel?
How many units of the 58 inch frame fit in a carton?
Do you supply the tempered glass with the frame?
Do you build a custom touch frame in this profile?
Also quoted as an IR touch frame, a touch screen or an overlay
Ask ten buyers for this part and you get four different names for it: infrared touch frame, IR touch frame, infrared touch screen and touch overlay. Nothing changes in the box. It is an aluminium rectangle with LEDs down two sides, photodiodes down the other two, and a controller board in the bottom rail. If your drawing is titled “IR touch screen” but your housing already carries the glass, you still need the frame and not a display — we quote it either way.
Half of these frames never go into a new machine at all. They go onto a TV or a monitor that is already on the wall, and the buyer wants a finger to work on it. Same extrusion, same controller, ordered with a longer cable — the overlay guide covers the fit.
If your enquiry uses a name not listed here, send it anyway — a photo of the old part or the housing opening settles it faster than any glossary. Full terminology list →
Tell us the size. We will tell you what fits.
Send a drawing, a size, or just a photo of the screen you are building around. Our engineers reply with a matched part and a price within 12 working hours.