86 inch infrared touch frame
86 inch is the largest size we hold production tooling for. Above this, frames are built to order, so lead time extends by roughly a week.
FOB Shenzhen, frame only, 1–50 pcs. Add $105 for 3 mm tempered glass. Volume tiers quoted on request.
The 86 inch, photographed before packing
Every unit is powered up and touched at nine points before it goes into the tube. At 1930 mm wide the finished frame weighs about 10.6 kg, which is why it travels in a tube with foam ends rather than a flat carton.
- 1930 × 1101 mm outer, 1904 × 1071 mm active area
- 2–40 touch points, USB HID, no driver for Windows, Android or Linux
- 302 pcs in stock, leaves in 3–7 days
Spare LED tubes. Tubes and filter strips are stocked for every size listed, so a dead emitter is a part swap rather than a new frame.
Ships knocked down. Four extrusions and four corners in one tube. Flat-packed freight runs about a third cheaper than a crated assembled frame.
What the 86 inch frame fits
The active area is 1904 × 1071 mm — a standard 86 inch 16:9 panel. The frame adds 13 mm on three sides and 19 mm at the bottom, which is where the controller PCB and USB cable sit.
- Outer frame: 1930 × 1101 mm, 9.5 mm deep
- Housing cut-out: leave 1934 × 1105 mm plus 3 mm clearance for the cable
- Glass clearance: up to 5 mm thick; 8 mm with the wide-gap version
- Mounting: front-flush with M3 inserts, or side brackets
Typical builds at this size: auditorium display, command room board, flagship showroom.
86 inch frame — options and unit price
Indicative FOB Shenzhen prices at 10-point configuration. Higher touch counts add controller cost, not sensor cost, so the jump is smaller than most buyers expect.
| Configuration | 1–9 pcs | 10–49 pcs | 50–199 pcs | 200+ pcs |
|---|---|---|---|---|
| 10-point | $330 | $310 | $290 | $264 |
| 20-point | $330 | $310 | $290 | $264 |
| 32-point | $350 | $329 | $308 | $280 |
| 40-point | $370 | $347 | $325 | $296 |
| + 3 mm tempered glass | + $105 | + $94 | + $86 | + $79 |
86 inch frame — full specification
| Mechanical | |
| Adopted screen | 86" 16:9 (active area 1904 × 1071 mm) |
|---|---|
| Frame outer size | 1930 × 1101 mm (± 1.0 mm) |
| Bezel width | 13 mm side / 19 mm bottom (15.5 mm uniform optional) |
| Frame depth | 9.5 mm |
| Frame material | Aluminium alloy 6063, black anodised |
| Net weight | 3.0 kg |
| Touch performance | |
| Touch points | 2 / 4 / 6 / 10 / 16 / 20 / 32 / 40 |
| Resolution | 32,768 × 32,768 (interpolated) |
| Response time | ≤ 8 ms |
| Report rate | 200 Hz |
| Accuracy | ± 2 mm (typical, centre 90 % area) |
| Minimum touch object | 5 mm — 3 mm with fine-tip option |
| Electrical & interface | |
| Interface | USB 2.0 HID, plug-and-play; RS232 optional |
| Power | USB 5 V, < 200 mA |
| Operating system | Windows 7/10/11, Android, Linux, Chrome OS |
| Environment & compliance | |
| Operating temperature | −20 °C to +70 °C |
| Humidity | 10 – 90 % RH, non-condensing |
| Ambient light | Up to 30,000 lux (direct-sunlight model on request) |
| MTBF | ≥ 30,000 hours |
| Touch life | > 50 million touches |
| Certification | CE, FCC, RoHS |
Values are typical for this size. Guaranteed limits are stated on the datasheet issued with your order.
What happens after the carton is open
A frame is not finished hardware until it is calibrated against the display it sits on. Three things ship with this size to get you there, and none of them are extras.
No driver, on any system
USB HID digitizer. Windows 10/11, Android, Linux and ChromeOS enumerate it without installing anything. macOS reports single point only — worth knowing before you commit.
Calibration tool and profile
Windows and Linux builds, 4/9/25-point runs, written to the controller so it survives a power cycle. Stuck? A ten-minute remote session with our engineer calibrates it with you.
Installation sheet for this size
Clearance, 0.5 N·m torque, ground under 4 Ω, 3 m passive USB limit — plus the symptom table that covers most first-install problems.
Installation guide · Calibration & software · OS compatibility
86 inch frame questions
What is the outer size of a 86 inch frame?
Can I get this size with a different bezel?
How many units of the 86 inch frame fit in a carton?
Do you supply the tempered glass with the frame?
Do you build a custom touch frame in this profile?
Naming, for the benefit of your purchasing team
Multi touch frame, infrared multi-touch frame, IR touch panel — all of them refer to the same assembly described on this page. The touch count is set by the controller and the LED pitch, not by the name, so a 10-point and a 40-point version are physically identical from the outside.
At 86 inch this is what the trade calls a large touch frame or a large format infrared touch frame. Practically it means two things: it ships knocked down as four extrusions and four corners to keep freight sane, and the corner joints carry the accuracy. Above 200 inch the aluminium is spliced too — the touch surface stays continuous, only the extrusion is joined.
Two questions decide the fit on a retrofit: the lit area of the display (not the diagonal on the box) and whether the USB port stays alive when the screen sleeps. Get those right and the install is fifteen minutes with a screwdriver.
If your enquiry uses a name not listed here, send it anyway — a photo of the old part or the housing opening settles it faster than any glossary. Full terminology list →
Tell us the size. We will tell you what fits.
Send a drawing, a size, or just a photo of the screen you are building around. Our engineers reply with a matched part and a price within 12 working hours.